In the event that you have a Spectrum Cable Box and are seeking for the codes and instructions on how to configure it, you have arrived at the right place. This page is a list of the Spectrum Cable Box tv remote codes for various brands of Spectrum Cable Box. This page also contains instructions on how to program Spectrum remote to the Cable Box using two different techniques.

Read More : How You Can Reset a Westinghouse TV Remote Control

Spectrum Cable Box TV Remote Codes List

Pioneer: 001, 034, 105, 063, 051, 063, 076

Scientific Atlanta: 001, 042, 003 041, 045, 046

Samsung: 001, 030

Motorola: 002, 148, 111

Pace: 002, 001, 005

General Instrument: 103, 104, 005

Hamlin: 055, 049, 050

Digeo: 153

Jerrold: 005, 103, 004, 101, 069, 009, 008

Magnavox: 012, 010

Memorex: 052

Moxi: 252, 111, 153

Hitachi: 055, 103

Infusion: 192

Panasonic: 047, 044

Philips: 012, 006, 020, 013

Pulsar: 052

Regal: 050, 049

Regency: 057

RCA: 047

Sony: 108

Sprucer: 047

Sky: 204, 230

Tocom: 040, 039, 056

Toshiba: 052

Telnet: 354

Viewstar: 015, 012

Zenith: 052, 100, 060, 093

How to Program a Spectrum Remote Control to Control a Cable Box ?

Step 1: Make certain that your cable box is turned on.

Step 2: Keep your Spectrum remote pointing in the direction of your Cable box.

Step 3: For a few seconds, press and hold the ‘CBL’ button on your remote. On your remote, the CBL button is the Component button for the Cable Box. When the small LED light on the Component button illuminates, release the button.

Step 4: Enter the right three-digit code for the brand of cable box. The remote codes were previously mentioned in this article.

Step 5: Press the Power button on your device. You have received the right code if your device activates. If the first code does not work, try the second. Alternately, you can experiment with the volume controls.

Step 6: Finally, by hitting the Component button a second time, the codes are saved. In other words, keep pressing the ‘CBL’ button until the small LED button blinks twice, indicating that your codes have been successfully stored.

The Another Method to Program Spectrum Remote to Cable Box

Step 1: Ascertain that your cable box is turned on.

Step 2: Face your Spectrum remote control towards the direction of your Cable box.

Step 3: Simultaneously press and hold the On/Off and Ok/Sell buttons for a few seconds, or until the ‘CBL’ button illuminates.

Step 4: For a few seconds, press and hold the ‘CBL’ button on your remote.

Step 5: Enter the proper three-digit code for the brand of your cable box. The remote codes were previously mentioned in this article. If your gadget powers down, this indicates that you have the right code. If not, attempt the following code. Additionally, you may experiment with the Volume buttons.

Step 6: Final step is to save the codes by pushing the CH+ button a second time until the small LED button blinks twice, indicating that the codes have been successfully stored.

We encourage you to utilise our search box to look for any additional codes you may require. Additionally, you may contact us through the comment area or by sending us an email. We’ll look for the code and put it here whenever we find it.

What should I do if my spectrum remote isn’t working?

Troubleshooting Procedures

1. Make sure your batteries are up to date.

2. Check to see if your Spectrum Receiver (cable box) is operational.

3. Change the channels on your receiver by pushing the buttons on the back of the receiver (if available).

4. Clear the area surrounding your receiver of any items (such as furniture).

5. Adjust the angle of your receiver so that it can detect your remote control device.

Error codes for Spectrum Cable Boxes are shown below with Solution

Error – DUI, DMI (No Signal/Picture)

Solution – Check for broken or loose wires, or re-calibrate your Spectrum signal.

Error – DI (A new version of the user manual is now available.)

Solution – Replace the battery in your cable box and wait 15 minutes to an hour for the instructions to refresh.

Error – EC220, E220 (Attempting to receive or purchase HD programmes on a television or receiver with a standard definition (SD) signal)

Solution – If you have an SD television, be sure you buy SD content, and if you have an HD set, try refreshing your signals to see if you can get better reception.

Error – Error 1, Error 5, Error 7 (Hardware failure, for example, a cable box)

Solution – If you need to replace your cable box, call Spectrum Customer Service.

Error – E14 (Inability to start the receiver)

Solution – If the problem persists, try resetting your cable box. If the problem still persists, contact Spectrum technical assistance.

Error – E09 (Failure of the memory or a dead battery)

Solution – Contact Spectrum technical support and inform them of the problem.

The Conclusion

In the above post, we have cover the topic how to Program Spectrum Remote to Cable Box. Also, we have explained the detailed list of Remote Control Codes for Spectrum Cable Boxes and Error codes for Spectrum Cable Boxes.

Thanks for reading.